PREPARATION AND APPLICATION
Magnolia Home by Joanna Gaines® Pre-Stain Conditioner, along with sanding, is essential in helping prepare interior bare or freshly stripped wood surfaces for an even and consistent color while staining. Use this product with Magnolia Home by Joanna Gaines Water-Based Interior Wood Stain to enhance the natural beauty of your interior wood surfaces.
PREPARATION
- All surfaces must be clean, free of dust, oil, grease, wax, polish, glue and all other foreign substances.
- New Wood: Sand the wood thoroughly with medium grit sandpaper and progress to fine grit sand paper (#180 – 220 grit). Always sand in the direction of the wood grain. Sand smooth and remove all dust prior to stain application. A tack cloth can be useful in removing all dust from the surface.
- Previously Finished Wood: Strip the surface completely down to bare wood with a paint or varnish remover, making sure all previous finishes are removed. Surface must be sanded smooth and remove all dust prior to stain application. A tack cloth can be useful in removing all dust from the surface.
APPLICATION
- Stir thoroughly before using. Do not shake or thin. Use a nylon or nylon/polyester brush or a saturated clean cloth and apply liberally to all areas of the wood surface including edges. Allow to penetrate between 5 to 10 minutes and then wipe off any excess with a clean, dry cloth. Sand lightly prior to staining to remove grain raise. Allow Pre-Stain Conditioner to dry for up to 20 minutes before applying Magnolia Home by Joanna Gaines Water-Based Wood Stain. Follow all label instructions.
CAUTIONS/LIMITATIONS
- Not for use with oil-based stains. For oil-based stains pretreat wood with an oil-based pre-stain wood conditioner.
- Shelf life under normal conditions is two years unopened.
DRY TIME @ 77°F & 50% RH
Longer dry time may be required in cooler temperatures and higher humidity.
- To Touch: After 10 mins
- To Apply Stain: After 10 mins
Clean-Up & Disposal
- Clean all tools and equipment with warm, soapy water.
- Do not dispose of this product down a drain. If spilled, contain material and remove with an inert absorbent.
- Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. For recycling or disposal of empty containers, unused product and soiled rags, contact your household refuse collection service.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.
GENERAL INFORMATION
WARNING IRRITANT CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY TRACT IRRITATION. CONTAINS: ETHYLENE GLYCOL AND CRYSTALLINE SILICA. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING VAPORS, SPRAY MIST AND SANDING DUST. Sanding, grinding or abrading may release sanding dust, which may be harmful if inhaled and has been shown to cause lung damage or cancer with long term exposure. Do not breathe dusts, vapor, or spray mist. To avoid breathing in dust, vapors, and spray mist, open windows and doors or use other means to ensure fresh air entry during application, drying, sanding, and/ or abrading. If properly used, a respirator (NIOSH approved with particulate pre-filter) may offer additional protection and should be used if adequate ventilation cannot be provided; obtain professional advice before using. If you experience eye watering, headaches, or dizziness during application or drying, increase fresh air or leave the area. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 20 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN-DO NOT TAKE INTERNALLY.
*LIFETIME LIMITED WARRANTY
Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: techservice@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
Cautions/Limitation
- IMPORTANT! Do not open can without reading instructions.
- Shake can thoroughly before opening for application.
- Stir before and during application.
- For tint bases-do not use without addition of colorant.
- Do not use on floors.
- Keep from freezing.
WARNING IRRITANT:
CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY TRACT IRRITATION. CONTAINS: ETHYLENE GLYCOL AND CRYSTALLINE SILICA. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING VAPORS, SPRAY MIST AND SANDING DUST. Sanding, grinding or abrading may release sanding dust, which may be harmful if inhaled and has been shown to cause lung damage or cancer with long term exposure. Do not breathe dusts, vapor, or spray mist. To avoid breathing in dust, vapors, and spray mist, open windows and doors or use other means to ensure fresh air entry during application, drying, sanding, and/or abrading. If properly used, a respirator (NIOSH approved with particulate pre-filter) may offer additional protection and should be used if adequate ventilation cannot be provided; obtain professional advice before using. If you experience eye watering, headaches, or dizziness during application or drying, increase fresh air or leave the area. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 20 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
-
Int/Ext
Int
-
Tint Base/Max Tint Load
No. M8000 Tint Base 29 fl oz / 3 fl oz (quart)
-
Resin Type
Acrylic
-
Coverage
Up to 400 sq ft/gal, depending on application method and substrate porosity.
-
Viscosity
75 – 85 KU
-
Dry Time
@ 77°F & 50% RH
-
Dry To Touch
1 hour
-
Dry To Topcoat
1 hour
PREPARATION AND APPLICATION
Magnolia Home by Joanna Gaines® Wood Stain delivers oil-like performance without the odor in a thick, fast-drying water-based formula. This product is available in a curated palette, hand-picked by Joanna Gaines to enhance the natural beauty of your interior wood surfaces. Tint this product to any one of the colors in the 12-color palette, and transform your interior wood surface(s) to their new, beautiful color.
PREPARATION
- All surfaces must be clean, free of dust, oil, grease, wax, polish, glue and existing coatings before staining. To ensure the best results and consistent absorption of the stain into the wood, start by using Magnolia Home by Joanna Gaines Pre-Stain Conditioner and follow all label instructions.
- New Wood: Sand with #120-grit sandpaper followed by #180-grit or finer for a smoother finish if desired. Remove all dust.
- Previously Finished Wood: Lightly sand surface with a 400-grit sandpaper. Remove all dust.
APPLICATION
- Stir stain thoroughly before and occasionally during use. Do not thin. Always test stain on an inconspicuous area of the wood to verify desired color. Apply stain in the direction of the grain with a brush or clean cloth. Allow the stain to penetrate up to 5 minutes to achieve desired color. The more time the stain is allowed to penetrate, the richer and darker the color will be. Remove stain that has not absorbed into the wood with a clean cloth. Wipe in the direction of the grain, while blending light and dark areas to obtain uniform color. Do not allow stain that has not penetrated into the wood to dry on the wood surface. To darken the color, apply a second coat after 1 hour, repeating directions above. Do not sand between coats of stain. Allow stain to dry for a minimum of 1 hour (dry time may be longer due to high humidity, low temperatures, or inadequate ventilation) before applying a Magnolia Home by Joanna Gaines clear protective finish.
CAUTIONS/LIMITATIONS
- Protect from freezing.
- Always test stain on an inconspicuous area of the wood to verify desired color.
- Shelf life under normal conditions is two years unopened.
- Slight ambering may occur when these clear finishes are applied over light-colored stains. Always spot test on an inconspicuous area to ensure satisfactory results.
DRY TIME @ 77°F & 50% RH
Allow to dry between each coat.
- Dries to touch in 1 hour
- Topcoat 1 hour
Clean-Up & Disposal
- Clean all tools and equipment with warm, soapy water.
- Do not dispose of this product down a drain. If spilled, contain material and remove with an inert absorbent.
- Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. For recycling or disposal of empty containers, unused product and soiled rags, contact your household refuse collection service.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.
GENERAL INFORMATION
WARNING IRRITANT CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY TRACT IRRITATION. CONTAINS: ETHYLENE GLYCOL AND CRYSTALLINE SILICA. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING VAPORS, SPRAY MIST AND SANDING DUST. Sanding, grinding or abrading may release sanding dust, which may be harmful if inhaled and has been shown to cause lung damage or cancer with long term exposure. Do not breathe dusts, vapor, or spray mist. To avoid breathing in dust, vapors, and spray mist, open windows and doors or use other means to ensure fresh air entry during application, drying, sanding, and/ or abrading. If properly used, a respirator (NIOSH approved with particulate pre-filter) may offer additional protection and should be used if adequate ventilation cannot be provided; obtain professional advice before using. If you experience eye watering, headaches, or dizziness during application or drying, increase fresh air or leave the area. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 20 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
*LIFETIME LIMITED WARRANTY
Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: techservice@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
Cautions/Limitation
- IMPORTANT! Do not open can without reading instructions.
- Shake can thoroughly before opening for application.
- Stir before and during application.
- For tint bases-do not use without addition of colorant.
- Do not use on floors.
- Keep from freezing.
WARNING IRRITANT:
CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY TRACT IRRITATION. CONTAINS: ETHYLENE GLYCOL AND CRYSTALLINE SILICA. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING VAPORS, SPRAY MIST AND SANDING DUST. Sanding, grinding or abrading may release sanding dust, which may be harmful if inhaled and has been shown to cause lung damage or cancer with long term exposure. Do not breathe dusts, vapor, or spray mist. To avoid breathing in dust, vapors, and spray mist, open windows and doors or use other means to ensure fresh air entry during application, drying, sanding, and/or abrading. If properly used, a respirator (NIOSH approved with particulate pre-filter) may offer additional protection and should be used if adequate ventilation cannot be provided; obtain professional advice before using. If you experience eye watering, headaches, or dizziness during application or drying, increase fresh air or leave the area. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 20 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
-
Int/Ext
Int
-
Resin Type
Polyurethane/Acrylic
-
Net Weight
11.5 oz / 326 g
-
% Solids by Volume
11% ± 2%
-
% Solids by Weight
14% ± 2%
-
Coverage
15 – 20 sq ft per can
-
Viscosity
25 – 30 s (#1 Zahn Cup)
-
Dry Time
@ 77°F & 50% RH
PREPARATION AND APPLICATION
Magnolia Home by Joanna Gaines® Polyurethane clear finish provides a durable, long-lasting topcoat that allows the beauty of your newly stained interior wood surfaces to shine through. This water-based formula resists stains and scratches, protecting the desired look of your wood surfaces from day to day wear and tear. Available in two sheens: Matte and Semi-Gloss.
PREPARATION
- All surfaces must be clean, free of dust, oil, grease, wax, polish, glue and all other foreign substances.
- For refinishing, remove all wax or cleaner build-up with a wax stripper or degreaser prior to sanding. Sand all surfaces in the direction of the wood grain to desired smoothness. DO NOT USE steel wool. Remove all dust from sanded surfaces with tack cloth.
APPLICATION
- Shake can vigorously for 1 minute after mixing ball begins to rattle and often during use. Protect adjacent areas from overspray. Hold can vertically 12 inches from surface. Depress button fully and spray using an even, sweeping motion with slightly overlapping strokes.
- On unfinished wood, apply sufficient material to seal open joints, edges and end-grain. Apply thin coats to avoid runs and sags. Recoat within 1 hour. If unable to do so, wait a minimum of 72 hours, then lightly sand and recoat.
- Apply at least 3 coats on unfinished wood and 2 coats on surfaces already finished. After final coat, allow at least 24 hours before normal use.
- Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces.
- Floor Application: use a synthetic pad applicator or nylon/polyester brush and maintain a wet edge to avoid lap marks. Do not puddle, over-brush or overlap finishes. Sand lightly between coats with fine sandpaper. Remove all dust prior to applying additional coats.
CAUTIONS/LIMITATIONS
- Do not apply in direct sunlight or in temperatures below 55°F or above 90°F.
- Product appears milky when wet but dries to a crystal clear finish.
- Always spot test on an inconspicuous area to ensure satisfactory result.
DRY TIME @ 77°F & 50% RH
Note: Dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times.
- To Touch: 1 hour
- Sand or Recoat: 1 hour
- Light Use: 12 – 24 hrs
- Full Cure: 72 hrs
Clean-Up & Disposal
- Wet overspray can be removed with soap and water.
- After each use, clear valve by holding can upside down and spraying until only clear gas comes out.
- If spray button becomes clogged, wear eye protection, wipe off button opening with lacquer thinner. Do NOT stick pin in spray button opening.
- Wipe off tip before storing.
- Do not burn or place in home trash compactor.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.
GENERAL INFORMATION
VENTILATION REQUIRED: To avoid inhalation and combustion hazards (see below), DO NOT use this product unless you can achieve cross-ventilation by opening windows and doors during application and drying. CONTAINS 1-METHYL2-2PYRROLIDONE, ISOPROPYL ALCOHOL AND DIMETHYLETHER. VAPOR HARMFUL. May affect the brain or nervous system causing dizziness, headache or nausea. CAUSES SERIOUS EYE DAMAGE. IRRITATES SKIN, NOSE AND THROAT. Do not breathe vapors or spray mist. If you experience eye watering, headaches or dizziness, increase fresh air, wear respiratory protection (NIOSH/MSHA TC 23C or equivalent) or leave the area. VAPORS MAY IGNITE EXPLOSIVELY. Do not spray near sparks, heat or open flame. Do not smoke. Vapors are heavier than air, and can travel at floor level to distant ignition sources. Extinguish all flames and pilot lights and turn off stoves, heaters, electric motors, high intensity lights and other sources of ignition during use and until all vapors are gone. WARNING-CONTENTS UNDER PRESSURE. Do not puncture or incinerate container. Do not expose to heat or store at elevated temperatures above 120° F. Prolonged exposure to sun maycause bursting.
FIRST AID: If you have difficulty breathing, leave area to obtain fresh air. If difficulty continues, get medical attention immediately. If swallowed, call physician immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water.
CAUTION: KEEP OUT OF REACH OF CHILDREN-DO NOT TAKE INTERNALLY.
*LIFETIME LIMITED WARRANTY
Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: techservice@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
Cautions/Limitation
- IMPORTANT! Do not open can without reading instructions.
- Shake can thoroughly before opening for application.
- Stir before and during application.
- For tint bases-do not use without addition of colorant.
- Do not use on floors.
- Keep from freezing.
WARNING IRRITANT:
CAUSES EYE AND SKIN IRRITATION. MAY CAUSE RESPIRATORY TRACT IRRITATION. CONTAINS: ETHYLENE GLYCOL AND CRYSTALLINE SILICA. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING VAPORS, SPRAY MIST AND SANDING DUST. Sanding, grinding or abrading may release sanding dust, which may be harmful if inhaled and has been shown to cause lung damage or cancer with long term exposure. Do not breathe dusts, vapor, or spray mist. To avoid breathing in dust, vapors, and spray mist, open windows and doors or use other means to ensure fresh air entry during application, drying, sanding, and/or abrading. If properly used, a respirator (NIOSH approved with particulate pre-filter) may offer additional protection and should be used if adequate ventilation cannot be provided; obtain professional advice before using. If you experience eye watering, headaches, or dizziness during application or drying, increase fresh air or leave the area. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 20 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
