KILZ® Porch & Patio Floor Paint

Preparation^†

The following steps and products are required.

• All surfaces must be clean, sound, dry and free of any dirt, oil and grease. Remove mildew stains with a mildew stain-removing product such as a wood cleaner and brightener.

• Scuff sand any glossy surfaces. If making repairs, use stainless steel or galvanized nails to prevent nail staining. Countersink nail heads, repair imperfections and sand smooth. Remove all dust with a damp cloth, allow to dry.

• New or Weathered Wood: Prepare surface with a wood cleaner and brightener. Lightly sand to remove remaining wood fibers/ fuzz. Prime with KILZ 3 Premium Primer.

• Painted Wood Surfaces: To strip an old coating, use a wood stain & finish stripper, then neutralize with a wood cleaner and brightener. For optimal adhesion, apply KILZ 3 Premium Primer before applying topcoat.

• Uncoated Concrete or Masonry Surfaces: Allow new surfaces to cure 30 days. Prepare surface with a concrete and masonry cleaner and etcher. Then prime using KILZ Concrete & Masonry Bonding Primer

• Painted Concrete or Masonry Surfaces: To clean a painted surface in sound condition, use a concrete and masonry cleaner and degreaser. To strip an old coating, use a concrete and masonry paint stripper. Use a concrete and masonry cleaner and etcher to etch all exposed concrete, followed by KILZ Concrete & Masonry Bonding Primer before applying topcoat.

Application

• For best results, apply when air and surface temperatures are between 50-90°F.

• Stir paint occasionally. When working with more than one can of the same product, intermix to ensure color uniformity.

• Use a high quality 3/8"-1/2" nap roller cover, nylon/polyester brush or an airless sprayer (.015"-.019" spray tip, 60 mesh filter). Spread rates may vary depending on the surface texture, porosity and application method. Apply second coat in the opposite direction of the first. Do not dilute if using a roller or brush; however, if using a sprayer and thinning is required, dilute with water at a rate of no more than 1/2 pint per gallon. Certain colors may require more than one coat to achieve complete hide and coverage.

• COVERAGE: Rough surfaces: 200-300 sq. ft; Smooth surface 300-400 sq. ft.

Dry Time

• Dries to touch in 1 Hour; 4-6 Hours to Recoat. Longer dry time required in cooler temperatures and in higher humidity. Allow 72 hours before subjecting to normal use. After 4 weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent. Dry paint film provides a mildew resistant finish.

Clean up & Disposal

• Clean equipment and paint spatters with warm, soapy water. If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current governmental regulations.

• Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.

Cautions/Limitations

• Protect from freezing.

• Do not use on garage floors.

• For best results, apply at temperatures between 50°F-90°F. Temperatures above 90°F may affect the application such as drying too fast. Avoid painting in direct sun. NOTE: If the surface is hot to the touch it should be considered too hot to apply this coating.

• Avoid heavy traffic for 24 hours.

• Allow four weeks before washing or cleaning for full cure.

• Shelf life under normal conditions is two years unopened.

*Limited Warranty

For one year from the date of purchase, Masterchem Industries LLC warrants to the original residential consumer purchaser (1) that the product meets Masterchem Industries LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event that this product proves to be defective within one year from the date of purchase, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty.  Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: techservice@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

General Information

IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS

^†Warning!

If you scrape sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

WARNING: Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.

CAUTION! Sealed surfaces may become slippery when wet. Use caution when walking on surface when moisture is present.

Warning! Irritant!

HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer additional protection; obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.

First Aid

• If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
• In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention.
• For skin, wash thoroughly with soap and water.
• If swallowed, get medical attention immediately.

Caution

• KEEP OUT OF REACH OF CHILDREN.
• DO NOT TAKE INTERNALLY.

• Base

  Ultra Pure White, Deep, and Pre-Tint

• Int/Ext

  Int/Ext

• Color

  Ultra Pure White, Deep, Silver Gray, Slate Gray

• Coverage Rate

  200-400 sq. ft./gal. depending on application method and substrate porosity. Does not include the loss of material from spraying.

• Coverage - Low

  200 sq. ft.

• Mils Wet

  8

• Mils Dry

  2.9

• Coverage High

  400 sq. ft.

• Mils Wet

  4

• Mils Dry

  1.4

• Viscosity

  90 - 100 KU

• VOC

  50 g/L

• Volume Solids

  37%

• Weight Solids

  50%

• Flashpoint

  N/A