KILZ® 1-Part Epoxy Acrylic Concrete & Garage Floor Paint

Preparation^†

The following steps and products are required.

• New and Uncoated Concrete or Masonry Surfaces:
  New concrete must cure for a minimum of 30 days. For proper penetration and adhesion of topcoat, use a product such as KILZ Concrete & Masonry Cleaner & Etcher to clean and etch the surface. Apply a product such as KILZ Concrete & Masonry Bonding Primer to increase adhesion of topcoat to the surface.

• Painted, Stained or Sealed Concrete:
  Option 1- To completely strip the entire surface, use a product such as KILZ Concrete & Masonry Paint Stripper.
  Option 2- To recoat over an existing coating, remove any loose or peeling paint and scuff sand the surface. Use a product such as KILZ Concrete & Masonry Cleaner & Degreaser to clean previously coated surfaces in sound condition. Use a product such as KILZ Concrete & Masonry Cleaner & Etcher to clean and etch any bare concrete area.

Application

• DO NOT DILUTE.

• USE ONLY WITH ADEQUATE VENTILATION.

• Intermix all cans of same product to ensure color uniformity. Stir before applying.

• For best results, apply when air and surface temperatures are between 50-90°F.

• Apply a thin, even coat using a 3/8" nap roller cover, pad applicator or a nylon/polyester brush or an airless sprayer (.015"-.021"spray tip, 60 mesh filter).

• COVERAGE: 400-500 sq. ft. per gallon on smooth surfaces and of 300-400 sq. ft. per gallon on rough surfaces.

• Allow first coat to dry 24 hours before deciding if a second coat is necessary. For uniformity, apply a second coat (in a criss-cross direction).

• DO NOT APPLY MORE THAN TWO COATS. An annual touch-up may be required in areas subject to tire traffic.

Dry Time

• Dries to touch in 2 hours. Longer dry time required in cooler temperatures and in higher humidity.

• Re-coat time 4-6 hours.

• The floor may be subjected to light foot traffic after 24 hours. Allow 72 hours before subjecting surface to heavy foot traffic or repositioning furniture.

• Allow 7 days before subjecting to automotive tires. Premature heavy traffic will cause paint failure requiring spot recoating. If necessary, corrugated cardboard may be used underneath automobile tires after 72 hours.

• Wait at least 30 days before rinsing or cleaning. Use a mild detergent as needed. Abrasive cleaners and pressure-washers should be used carefully to avoid premature paint failure.

Clean up & Disposal

• Clean all tools and equipment with soap and clean water.

• If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current governmental regulations.

• Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.

Cautions/Limitations

• Protect from freezing

• For best results, apply at temperatures between 50°F - 90°F. Temperatures above 90°F may affect the application such as drying too fast. Avoid applying in direct sun. NOTE: If the surface is hot to the touch it should be considered too hot to apply this coating.

• Avoid heavy traffic for 24 hours.

• DO NOT APPLY MORE THAN TWO COATS

• Allow 30 days before washing or cleaning for full cure.

• Shelf life under normal conditions is two years unopened.

*Limited Warranty

For one year from the date of purchase, Masterchem Industries LLC warrants to the original residential consumer purchaser (1) that the product meets Masterchem Industries LLC’s manufacturing specifications, and (2) the performance of this product when applied according to the label instructions and specifications. In the event that this product proves to be defective within one year from the date of purchase, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty.  Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: techservice@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

General Information

IMPORTANT! DO NOT OPEN CAN WITHOUT READING INSTRUCTIONS

^†Warning!

If you scrape sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respir tor to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

WARNING: This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

CAUTION! Surfaces may become slippery when wet. Use caution when walking on surface when moisture is present.

Warning! Irritant!

HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer additional protection; obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use.

First Aid

• If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
• In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention.
• For skin, wash thoroughly with soap and water.
• If swallowed, get medical attention immediately.

Caution

• KEEP OUT OF REACH OF CHILDREN.
• DO NOT TAKE INTERNALLY.

• Base

  White Base, Deep Base, Silver Gray, Slate Gray

• Int/Ext

  Int/Ext

• Color

  White Base, Deep Base, Tint Base

• Coverage Rate

  300-500 Sq. Ft./Gal.

• Coverage - Low

  300 sq. ft.

• Mils Wet

  5.3

• Mils Dry

  1.6

• Coverage High

  500 sq. ft.

• Mils Wet

  3.2

• Mils Dry

  1

• VOC

  50 g/L

• Volume Solids

  31%

• Weight Solids

  41%

• Viscosity

  90 - 100 KU

• Flashpoint

  N/A