KILZ® RESTORATION™
Interior Primer

Surface Preparation†

The following steps arerecommended for product performance.

• All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew, loose peeling paint, rust and all other foreign substances.

• If washing is necessary, use a non-soapy detergent or a TSP substitute, rinse well and allow to dry.

• Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.*

• ^†Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before priming.

*WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Centre at 1-800-424-LEAD or log on to www.epa.gov/lead.

• Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming.
• Masonry, Brick, Stucco and Plaster: KILZ RESTORATION Primer may be used on clean, dry, aged interior masonry surfaces that have cured (dried) at least 30 days.
•  Fire Restoration: It is critical to clean damaged surfaces thoroughly before priming.

Application

• Eye protection is recommended. For spray applications, a small amount of water (no more than 240 ml per 3.79 L) may be added. Do not thin for stainblocking applications.

• Only apply if surface, air and product temperatures are between 10°- 32° C. Stir thoroughly before and occasionally during use. Apply using a brush, roller or sprayer.

• Brush – High quality Nylon/Polyester

• Roller – High quality 10 – 13 mm nap on smooth surfaces or 13 – 19 mm nap on semi-rough or porous surfaces.

• Airless spray – .017 - .021 tip / 60 mesh filter

• Prime the entire surface to ensure a uniform appearance of the topcoat.

• Stainblocking: After priming, test for stain bleed-through by applying the topcoat to a small section. If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoating the entire area. If bleeding continues, a longer dry time is needed before topcoating.

• Sealing Odours: For persistent odours, apply a second coat of primer before topcoating. If odour continues, a longer drytime is needed before topcoating.

• Tinting: KILZ RESTORATION Primer may be tinted with up to 15 mL of universal colourant per 3.79 L. Tinting to a lighter shade than the topcoat is recommended.

• Coverage: 27.87 - 37 m2 (300 - 400 sq. ft.) per 3.79 L depending on application method and surface porosity.

• Dry Time @ 25° C / 50% RH: Touch 30 minutes, Recoat 1 hour.

Clean up & Disposal

• Clean equipment and paint spatters with warm, soapy water.

• Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.

• If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current government regulations

WARNING!

MAY IRRITATE EYES AND SKIN. Avoid contact with eyes, skin and clothing. Do not breathe fumes. Keep out of reach of children. Wear eye protection and protective clothing. Use only adequate ventilation.

FIRST AID TREATMENT

Contains: BARIUM SULFATE AND 2-ETHYLHEXYL BENZOATE. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 20 minutes. If on skin, rinse well with water. If inhaled, move person to fresh air.

LIFETIME LIMITED WARRANTY

Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label
for so long as you reside in your home. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Masterchem Industries LLC unless extended by a provincial consumer statute. To obtain warranty service, write to: Technical Services, Masterchem Industries LLC, 2750 Centre Avenue N.E., Calgary, AB T2A2L3, or email: techserve@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

For warranty service, call: 1-866-977-3711, or email: techservice@masterchem.com. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

• Base

  Water

• Int/Ext

  Interior

• Colour

  White

• Coverage - Low

  28 m²

• Mils Wet

  5.3

• Mils Dry

  2.0

• Coverage High

  37 m²

• Mils Wet

  4.0

• Mils Dry

  1.5

• Finish @ 85°

  <10

• Min Application Temp

  10°C

• Max Application Temp

  32°C

• Viscosity

  90 -100 KU

• Dry To Touch

  30 min

• Dry To Recoat

  1 hour

• Max Tint

  60 ml

• VOC

  75 g/L

• Brush

  Nylon/Poly

• Roller - Smooth

  10 - 12 mm nap

• Roller - Porous

  12 - 14 mm nap

• Spray Tip

  .015" - .021"

• Spray Filter

  60 mesh

• Spray Pressure

  2,500 - 3,000

• Volume Solids

  37.5% (+/-) 2%

• Weight Solids

  54.0% (+/-) 2%

• Flashpoint

  N/A